CLEAN GREEN

TECHNICAL PRODUCT BULLETIN #SW-44
USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION
ORIGINAL LISTING DATE: AUGUST 5, 2010
"CLEAN GREEN"

I. NAME, BRAND, OR TRADEMARK
CLEAN GREEN (aka, CLEANGREEN® PLANET WASH) Type of Product: Surface Washing Agent

II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT
U.S. AG, LLC P.O. Box 368 Luthersville, GA 30251 Phone: (770) 927-3206 Fax: (770) 927-3968 E-mail: unitedstatesag@yahoo.com Web Site: http://unitedstatesag.com/ Exit (Mr. Carl Schneider)

III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS
U.S. AG, LLC 56 N Main Luthersville, GA 30251 Phone: (770) 927-3206 Fax: (770) 927-3968 E-mail: unitedstatesag@yahoo.com Web Site: http://unitedstatesag.com/ Exit (Mr. Carl Schneider)

IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION
1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: No special requirements. 3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required, however, goggles are recommended. If eye or skin irritation occurs, flush with plenty of fresh water. 4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days 4.b. Minimum storage temperature: 35°F 4.c. Optimum storage temperature range: 40°F to 120°F 4.d. Temperatures of phase separations and chemical changes: Stable

IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION

1. Flammability: Non-flammable (DOT: Non-hazardous)
2. Ventilation: No special requirements.
3. Skin and eye contact; protective clothing; treatment in case of contact: No special equipment or clothing required, however, goggles are recommended. If eye or skin irritation occurs, flush with plenty of fresh water.
4.a. Maximum storage temperature: 120°F continuous, 140°F up to 5 days
4.b. Minimum storage temperature: 35°F
4.c. Optimum storage temperature range: 40°F to 120°F
4.d. Temperatures of phase separations and chemical changes: Stable

V. SHELF LIFE
5 years in sealed polydrums or totes (as delivered).

VI. RECOMMENDED APPLICATION PROCEDURE
1. Application Method: Product may be applied to any oil coated surface, such as beaches, equipment, rocks, etc. A variety of pumps or sprayers may be used for direct application to contaminates, back-pack, drum pumps, pick-up sprayers, etc. 2. Concentration/Application Rate: Where ever higher oil concentrations occur use approximately a 1:10 dilution ratio (product:water). Lightly soiled areas will require a 1:10 to 1:30 ratio. 3. Conditions for Use: Residue from surface washing should be collected and disposed of according to local, state, and federal regulations. The collection of residue can be determined on a site by site basis based on best practices of the area.

VI. RECOMMENDED APPLICATION PROCEDURE

1. Application Method: Product may be applied to any oil coated surface, such as beaches, equipment, rocks, etc. A variety of pumps or sprayers may be used for direct application to contaminates, back-pack, drum pumps, pick-up sprayers, etc.
2. Concentration/Application Rate: Where ever higher oil concentrations occur use approximately a 1:10 dilution ratio (product:water). Lightly soiled areas will require a 1:10 to 1:30 ratio.
3. Conditions for Use: Residue from surface washing should be collected and disposed of according to local, state, and federal regulations. The collection of residue can be determined on a site by site basis based on best practices of the area.

VII. TOXICITY AND EFFECTIVENESS

a. Toxicity:

Material Tested	Species	LC50 (ppm)
CLEAN GREEN	Menidia beryllina Mysidopsis bahia	136.10 96-hr 70.70 48-hr
No. 2 Fuel Oil	Menidia beryllina Mysidopsis bahia	3.35 96-hr 2.24 48-hr
CLEAN GREEN & No. 2 Fuel Oil (1:10)	Menidia beryllina Mysidopsis bahia	4.73 96-hr 2.24 48-hr
Reference Toxicant (SLS)	Menidia beryllina Mysidopsis bahia	12.25 96-hr 10.53 48-hr

b. Effectiveness
NA

VIII. MICROBIOLOGICAL ANALYSIS
NA

IX. PHYSICAL PROPERTIES
1. Flash Point: >93°C 2. Pour Point: +25°F 3. Viscosity: 3.72 @40°C 4. Specific Gravity: 1.0691 @70°F 5. pH: 9.9 6. Surface Active Agents: CONFIDENTIAL 7. Solvents: CONFIDENTIAL 8. Additives: CONFIDENTIAL 9. Solubility: Miscible in oil, water, and solvents

X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS

Compound	Concentration (ppm)
Arsenic	0.0265
Cadmium	<0.005
Chromium	0.0985
Copper	<0.0150
Lead	<0.0100
Mercury	0.0005
Nickel	<0.0250
Zinc	0.2455
Cyanide	<0.300
Chlorinated Hydrocarbons	<5.0

Top of Page