EO ALL PURPOSE SOAP-LAVENDER
TECHNICAL PRODUCT BULLETIN #SW-50
USEPA, OEM REGULATIONS IMPLEMENTATION DIVISION
ORIGINAL LISTING DATE: NOVEMBER 17, 2010
“EO ALL PURPOSE SOAP-LAVENDER”
| I. NAME, BRAND, OR TRADEMARK |
|---|
| EO ALL PURPOSE SOAP-LAVENDER Type of Product: Surface Washing Agent |
| II. NAME, ADDRESS, AND TELEPHONE NUMBER OF MANUFACTURER/CONTACT |
|---|
| EO Products/Small World Trading Company 90 Windward Way San Rafael, CA 94901 Phone: (415) 945-1900 Fax: (415) 945-7117 E-mail: kimberly@eoproducts.com or sam@eoproducts.com Web Site: www.eoproducts.com (Ms. Kimberly Luce or Mr. Sam Borri) |
| III. NAME, ADDRESS, AND TELEPHONE NUMBER OF PRIMARY DISTRIBUTORS | |
|---|---|
| EO Products/Small World Trading Company 90 Windward Way San Rafael, CA 94901 Phone: (415) 945-1900 Fax: (415) 945-7117 E-mail: kimberly@eoproducts.com or sam@eoproducts.com Web Site: www.eoproducts.com (Ms. Kimberly Luce or Mr. Sam Borri) |
|
| IV. SPECIAL HANDLING AND WORKER PRECAUTIONS FOR STORAGE AND FIELD APPLICATION |
|---|
| 1. Flammability: Non-flammable (DOT: Non-hazardous) 2. Ventilation: Normal 3. Skin and eye contact; protective clothing; treatment in case of contact: Rinse thoroughly after use. Avoid eye contact. In case of such contact, immediately flush with large amounts of cool water for at least 15 minutes. Consult a physician if irritation develops. Protective gloves are recommended for extended or prolonged contact (e.g., immersing hands). Wear safety glasses if the method of use presents the likelihood of eye contact. Do not ingest. In case of ingestion, consult a physician. 4.a. Maximum storage temperature: 45°C 4.b. Minimum storage temperature: 4°C 4.c. Optimum storage temperature range: 22°C to 30°C 4.d. Temperatures of phase separations and chemical changes: Phase separation may occur at <15°C (but will restore to original condition at optimum temperature). |
| V. SHELF LIFE |
|---|
| Three (3) years (as delivered). |
| VI. RECOMMENDED APPLICATION PROCEDURE |
|---|
| 1. Application Method: EO ALL PURPOSE SOAP may be applied by pouring, spraying (when diluted 1:4), dispensing equipment, or by scrubbing machines. 2. Concentration/Application Rate: Apply EO ALL PURPOSE SOAP full strength (undiluted) to surface area by pouring or with dispensing equipment concentrating on areas with heaviest contamination first. Apply diluted (1:4 dilution rate) EO ALL PURPOSE SOAP with sprayer. Agitate and scrub well. Rinse thoroughly. For heavily contaminated surfaces, EO ALL PURPOSE SOAP should always be used full strength (undiluted). For average to light contamination, EO ALL PURPOSE SOAP may be diluted from 2x-10x with water. 3. Conditions for Use: During cleaning, contain the oil soaked area and collect residue. For sand and vegetation cleaning, a berm may be constructed down slope that will collect the residue for disposal. All disposal of residue should be done according to federal, state, and local regulations. In general, the technique used for the collection of the oil/soap residue should be determined by the on-site contractor based on the environment of the area to be cleaned, and equipment and materials available for collection. |
| VII. TOXICITY AND EFFECTIVENESS | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
a. Toxicity:
b. Effectiveness: |
| VIII. MICROBIOLOGICAL ANALYSIS |
|---|
| NA |
| IX. PHYSICAL PROPERTIES |
|---|
| 1. Flash Point: >93°C 2. Pour Point: +24°F 3. Viscosity: 349.5 cst @ 40°C 4. Specific Gravity: 1.0208 @60°F 5. pH: 5.88 6. Surface Active Agents: PROPRIETARY 7. Solvents: PROPRIETARY 8. Additives: PROPRIETARY 9. Solubility: Miscible in oil, water, and solvents |
| X. ANALYSIS FOR HEAVY METALS, CYANIDE, AND CHLORINATED HYDROCARBONS | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|