An official website of the United States government.

This is not the current EPA website. To navigate to the current EPA website, please go to www.epa.gov. This website is historical material reflecting the EPA website as it existed on January 19, 2021. This website is no longer updated and links to external websites and some internal pages may not work. More information »

New Mexico SIP: NM except Bernalillo County Part 41: Nonferrous Smelters-Sulfur

Regulatory Text: 
           NEW MEXICO ENVIRONMENTAL IMPROVEMENT BOARD
             P. O. BOX 26110/1190 ST. FRANCIS DRIVE
                    SANTA FE, NM  87502-0110


TITLE 20       ENVIRONMENTAL PROTECTION
CHAPTER 2      AIR QUALITY (STATEWIDE)

PART 41        NONFERROUS SMELTERS - SULFUR

(Approved by EPA 09/26/97 (62 FR 50518) at 52.1620(c)(66) effective 11/25/97. Dates in brackets within the regulation are State effective dates.)


100. ISSUING AGENCY:  Environmental Improvement Board.  [11-30-95]

101. SCOPE:  All geographic areas within the jurisdiction of the Environmental Improvement Board.  [11-30-95]

102. STATUTORY AUTHORITY:  Environmental Improvement Act. NMSA 1978, Section 74-1-8(A)(4) and (7), and Air Quality Control Act, NMSA 1978, Sections 74-2-1 et seq., including specifically, Section 74-2-5(A), (B) and (C).  [11-30-95]

103. DURATION:  Permanent.  [11-30-95]

104. EFFECTIVE DATE:  November 30, 1995.  [11-30-95]

105. OBJECTIVE:  The objective of this Part is to establish requirements and standards for nonferrous smelters to minimize sulfur emissions.  [11-30-95]

106. AMENDMENT AND SUPERSESSION OF PRIOR REGULATIONS:  This Part amends and supersedes Air Quality Control Regulation ("AQCR") 652-  Nonferrous Smelters -Sulfur last filed November 17, 1993.  [11-30-95]

     A.  All references to AQCR 652 in any other rule shall be construed as a reference to this Part.  [11-30-95]

     B.  The amendment and supersession of AQCR 652 shall not affect any administrative of judicial enforcement action pending on the effective date of such amendment nor the validity of any permit issued pursuant to AQCR 652. [11-30-95]

107.  DEFINITIONS: In addition to the terms defined in Part 2 - Definitions, as used in this Part:  [11-30-95]

     A.   "Captured fugitive emissions" means sulfur emissions which escape from various points in the smelting process and are captured.  [11-30-95]

     B.   "Exceedance" means the state of being exceeded.  [11-30-95]

     C.   "Existing nonferrous smelter" means a nonferrous smelter which was constructed and fully operational prior to September 1, 1971.  [11-30-95]

     D.   "Good operating conditions" means monitors operated in accordance with the specifications at 40 CFR Part 52, Appendices D and E.  [11-30-95]

     E.   "Malfunction" means any sudden and unavoidable failure of air pollution control equipment, process equipment or process to operate in an expected manner.  Failures that are caused entirely or in part by poor maintenance, careless operation or any other preventable equipment breakdown shall not be considered a malfunction.  [11-30-95]

     F.   "Median" means the middle value in a series of numbers below and above which fall an equal number of values.  [11-30-95]

     G.   "Modification" means a modification as defined by Section 74- 2-2.M, NMSA 1978.  [11-30-95]

     H.   "Modified nonferrous smelter" means any existing smelter that has incorporated a modification.  [11-30-95]

     I.   "New nonferrous smelter" means a nonferrous smelter, the construction of which commenced after September 1, 1971.  [11-30-95]

     J.   "Part" means an air quality control regulation under Title 20, Chapter 2 of the New Mexico Administrative Code, unless otherwise noted; as adopted or amended by the Board. [11-30-95]

     K.   "Startup" means the setting into operation of any air pollution control equipment, process equipment or process for any purpose.  [11-30-95]

     L.   "Sulfur" means elemental sulfur and the sulfur component of any sulfur mixtures or compounds.  [11-30-95]

     M.   "Sulfur dioxide" means the chemical compound containing two atoms of oxygen and one of sulfur.  [11-30-95]

     N.   "Uncaptured fugitive emissions" means sulfur emissions which escape to the atmosphere from various points in the smelting process due to leakage, materials charging and handling, transfer and storage, or other causes. [11-30-95]
     
108. DOCUMENTS:  Documents cited in this Part may be viewed at the New Mexico Environment Department, Air Quality Bureau, Runnels Building, 1190 Saint Francis Drive, Santa Fe, NM  87505. [11-30-95]


109. EMISSION LIMITATIONS - EXISTING OR MODIFIED NONFERROUS SMELTER:   The owner or operator of any existing or modified nonferrous smelter shall not permit, cause, suffer or allow:

     A.   Annual average emissions in excess of 7000 pounds of sulfur dioxide per hour except as provided for in Section 112 of this Part;

     B.   A median 3-hour running average to exceed 5309 pounds of sulfur dioxide per hour during any 365-day compliance period;

     C.   More than N occurrences of three-hour running average sulfur dioxide emissions in excess of the corresponding E values shown in the following table in any 365-day compliance period when there are malfunction or startup conditions:

 

N E
(number of occurrences) (pounds per hour of 
sulfur dioxide emissions)
0 3,000
1 49,000
2 45,500
4 42,300
7 39,200
12 36,200
20 33,400
32 31,300
48 29,200
68 27,200
94 25,600
130 23,800
180 21,700
245 20,000
330 18,700
435 17,200
560 15,800
710 14,600
890 13,200
1100 12,200
1100 7,800



                                                       [11-30-95]

     D.   More than N occurrences of three-hour running average sulfur dioxide emissions in excess of the corresponding E values shown in the following table in any 365-day compliance period when there are not malfunction or startup conditions:

  
 

N E
(number of occurrences) (pounds per hour of 
sulfur dioxide emissions)
0 12,200
240 10,700
510 9,800
810 8,700
1,140 7,800




                                                       [11-30-95]

          1.   Any three-hour average that includes a period of time when there are malfunction or startup conditions shall be included in either the cumulative occurrence limits of Sections 109.C or 109.D of this Part, at the choice of the smelter owner or operator;

          2.   Any three-hour average that does not include a period of time when there are malfunction or startup conditions shall be included in the cumulative occurrence table in Section 109.D of this Part;

     E.   The release of fugitive sulfur emissions to the atmosphere unless the owner or operator utilizes best engineering practices to minimize the release of such fugitive emissions.  Best engineering practices shall, as a minimum, include:

          1.   Maintaining and operating all furnaces, converters, and converter hoods so that leakage of gases to the atmosphere will be minimized to the maximum extent practicable;

          2.   Maintaining all ducts, flues, and stacks in leak-free condition;

          3.   Installing and operating tight-fitting exhaust hoods where feasible on all tapholes, launders, and other significant sources of fugitive sulfur emissions; and

          4.   Venting all captured fugitive emissions through the tallest stack serving the smelter;

     F.   Operation of the smelter without including all measured emissions to the atmosphere in compliance calculations.  [11-30-95]

110. EMISSION LIMITATIONS - NEW NONFERROUS SMELTER:  The owner or operator of a new nonferrous smelter shall not permit, cause, suffer or allow:

     A.  sulfur emissions to the atmosphere in excess of ten pounds of sulfur for every one hundred pounds of sulfur fed to the smelter;

     B.  the release of fugitive sulfur emissions to the atmosphere unless best engineering practices, including practices listed in Section 109.E of this Part, are utilized to minimize the release of such fugitive emissions. [11-30-95]

111. MONITORING - EXISTING OR MODIFIED NONFERROUS SMELTER:

     A.   Continuous Monitoring.  The owner or operator of an existing or modified nonferrous smelter shall maintain monitors in good operating condition which continuously measure and record the sulfur dioxide concentration and stack gas volumetric flow rate of the gases within the stacks serving all furnaces, liquid sulfur dioxide plants, converters, acid plants, reverberatory feed dryers, and stacks from which captured fugitive emissions are vented to the atmosphere.  Any continuous monitors required by this Section shall record the sulfur dioxide concentration and stack gas volumetric flow rate at least 95 percent of the time for any twelve consecutive calendar months.  The 95 percent data recovery shall only apply for the time or times that the stack is used to release sulfur dioxide to the atmosphere.  If the monitor does not measure the sulfur dioxide concentration and stack gas volumetric flow rate for the required amount of time, the smelter owner shall use alternative methods approved by the Department and the US EPA to supply the missing concentration data.  [11-30-95]

     B.   Sampling Locations.  The sampling point or points of the continuous monitoring system shall be located at least eight stack diameters (diameter measured at sampling point) downstream and two diameters upstream from any flow disturbance such as a bend, expansion, constriction or flame, unless another location is approved by the Department.  The sampling point for monitoring emissions shall be in the duct at the centroid (geometrical centered l.0 per cent area) of the cross-section if the cross-sectional area is less than 113 square feet or at a point no closer to the wall than six feet if the cross-sectional area is more than 113 square feet unless otherwise approved by the Department.  The sampling point shall be in an area of low spatial concentration gradient and shall be representative of the concentration in the duct.  [11-30-95]

     C.   Exemptions.  Upon the request of the owner or operator of the smelter, the Department may exempt stacks from this monitoring requirement if the Department determines that they do not carry more than ten (10) pounds per hour sulfur dioxide emissions.  [11-30-95]

     D.   Instrument Calibration and Data Retention.  Instruments and sampling systems installed and used pursuant to this Section shall be calibrated in accordance with the methods prescribed by manufacturer's recommended zero adjustment and calibration check procedures at least once every 24 hours of operation, unless the manufacturer specifies or recommends calibration checks more frequently.  The owner or operator of the smelter shall retain all raw data and quality assurance measurements and procedures for a minimum of three years.  [11-30-95]

     E.   Performance Audits of Monitoring System.  Instruments and sampling systems installed and used pursuant to Sections 111.A, 111.B, and 111.C above, shall be installed, operated and maintained in accordance with the performance specifications and other requirements set forth at 40 CFR Part 52, Appendices D and E. Alternative procedures for this paragraph may be used with approval of the Department and the EPA.  In the event that repair work is performed on the monitoring system, that could result in inaccurate readings, the owner or operator of the smelter shall demonstrate to the Department that the system continues to meet the applicable performance specifications.  The Department may require the owner or operator of the smelter to conduct performance tests as specified at 40 CFR Part 52, Appendices D and E at any time that the Department determines that such a test is necessary to verify the performance of the monitoring system. The Department and the US EPA may approve alternative means of verifying the performance of the continuous monitoring system.  The Department may also perform independent audits on the continuous monitoring system, utilizing Methods l, 2, 4 and 8, found at 40 CFR Part 60, Appendix A, or other applicable methods.  [11-30-95]

     F.   Test Notification, Reporting and Reevaluation of CEMS.  The owner or operator of an existing or modified nonferrous smelter shall:

          1.   Notify the Department at least forty-five (45) days in advance of the start of the field tests required at 40 CFR Part 52, Appendices D and E;

          2.   Submit a report to the Department within forty-five (45) days of the completion of any performance specification test required by this Part or the Department; and

          3.   Reevaluate the continuous emission monitoring systems installed and operated pursuant to Section 111.E of this Part at least once during any twelve (12) calendar months following the installation of such systems.  The evaluation shall demonstrate acceptability of zero and calibration drift, relative accuracy error, and calibration error of measurements contained in the applicable performance specification at 40 CFR Part 52, Appendices D and E, or as otherwise approved by the Department.  [11-30-95]

112. COMPLIANCE - EXISTING OR MODIFIED NONFERROUS SMELTERS:  Compliance with Section 109 of this Part shall be determined in accordance with the requirements specified in this Section:

     A.   Annual running average emissions shall be calculated at the end of each calendar day.  The smelter shall be in violation if two (2) consecutive annual averages exceed the emission limit and the second average exceeds the first average.  The smelter shall also be in violation if ten (10) consecutive annual averages exceed the annual average emission limit;

     B.   The median running 3-hour average for the previous 365 days shall be calculated at the end of each calendar day.  Such compliance determinations shall be calculated at the end of each day for each compliance period;

     C.   Compliance with the cumulative occurrence tables in Section 109 of this Part shall be determined on the basis of all running three-hour averages measured in the previous 365 days or less.  Such compliance determinations shall be calculated at the end of each day.  Three-hour averages shall be calculated at the end of each clock hour by averaging the hourly emissions for the preceding three (3) consecutive hours whenever each hour was measured in accordance with Sections 109 and 111.A, 111.B, and 111.C of this Part ;

     D.   If the smelter is not operating for an extended period of time, and with the approval of the Department, zeros may be recorded on an hourly basis without operating the continuous monitoring system if emissions to the atmosphere are shown to be below ten (10) pounds per hour;

     E.   A three-hour emissions average in excess of an emission level (E) is a violation if the number of all three-hour emissions averages that exceed the emission level (E) measured during the compliance period exceeds the cumulative occurrence limit (N);

     F.   The compliance period shall consist of the 365 days immediately preceding each day;

     G.   A three-hour emissions average can only violate the cumulative occurrence limit (N) of an emissions level (E) in the day containing the last hour in the average;

     H.   Multiple exceedances of a cumulative occurrence limit by different three-hour emissions averages containing any common hour constitute a single violation.  [11-30-95]

113. COMPLIANCE - NEW NONFERROUS SMELTERS:  Compliance with Section 110.A of this Part shall be determined in accordance with the requirements specified in this Section:

     A.   It shall be a violation of this Part if the sulfur removal requirement in Section 110.A of this Part is not achieved for any calendar month;

     B.   The owner or operator of any new nonferrous smelter shall calculate the sulfur removal rate for the smelter for each calendar month.  This calculation shall be done in accordance with a written plan approved by the Department and US EPA.  [11-30-95]

114. REPORTING:  Persons owning or operating any existing, modified or new nonferrous smelter shall submit quarterly reports to the Department for the periods January 1 through March 31, April 1 through June 30, July 1 through September 30 and October 1 through December 31 of each year. Each report shall be filed with the Department within forty five (45) days of the end of the quarterly period.  [11-30-95]

     A.   Existing and Modified Nonferrous Smelters.

          1.   The quarterly reports for existing and modified nonferrous smelters shall include:

               a.   the annual average emissions in pounds of sulfur dioxide per hour calculated at the end of each day;

               b.   all exceedances of the cumulative occurrence tables in Section 109 of this Part,  including the associated date, time, E value and N value; and

               c.   the twenty (20) highest running three-hour averages with the associated time and date of occurrence;

               d.   the median 3-hour running average for each compliance period in pounds of sulfur dioxide per hour at the end of each day. [11-30-95]

          2.   All three-hour running averages, E-values, N-values, and continuous monitoring measurements shall be retained by the owner or operator of any existing or modified nonferrous smelter for at least three (3) years. Upon request, the owner or operator of the smelter shall report such data in a timely manner to the Department.  [11-30-95]

     B.   New Nonferrous Smelters.  The quarterly reports for new nonferrous smelters shall include:

          1.   Sulfur removal rates for each calendar month;

          2.   Identification of all exceedances of the requirement in Section 110.A of this Part ; and

          3.   Identification of all periods of time for which notification was provided to the Department pursuant to Part 7 - Excess Emissions During Malfunction, Startup, Shutdown, or Scheduled Maintenance.  [11-30-95]

          4.   The owner or operator of any new nonferrous smelter shall retain all records utilized as the basis for the quarterly report for a period of at least three (3) years.  Upon request, such records shall be made accessible or reported to the Department.  [11-30-95]

115. FUGITIVE EMISSIONS EVALUATION:  No later than the end of the first two years of operation, the owner or operator of a modified smelter shall submit to the Department the results of an evaluation of the fugitive sulfur dioxide emissions from the smelter.  The evaluation shall contain the following information:

     A.   A measurement or accurate estimate of captured and  uncaptured fugitive emissions from the smelter.  The measurement or estimate shall contain the amount of both short-term and long-term fugitive emissions from the smelter.  The evaluation plan shall be approved in advance by the Department and shall specify the method used to determine the fugitive emission amounts;

     B.   A measurement or accurate estimate of the relative proportion (expressed as a percentage) of captured and uncaptured fugitive emissions produced by the following smelter processes:  Roaster or dryer operation; Calcine or dried concentrate transfer; Furnace operations (including feeding, slag return, matte and slag tapping); Matte transfer; and Converter operations. The measurement technique or method of estimation used to fulfill this requirement shall be approved in advance by the Department;

     C.   the results of a one year fugitive emission impact analysis. The study shall utilize sufficient measurements of fugitive emissions, meteorological conditions and ambient sulfur dioxide concentrations to associate fugitive emissions with specific measured ambient concentrations of sulfur dioxide.  The study shall describe in detail the techniques used to make the required determinations.  It shall include an analysis of the feasibility of using sulfur balance figures for the above determinations.  The design of the study shall be submitted within 60 days of the startup of the modified smelter for approval by the Department.  [11-30-95]

116. MONITORING EQUIPMENT:  In order to assess the sufficiency of the cumulative occurrence and emission limits contained in Section 109 of this Part and in order to maintain the ambient air quality standards for sulfur dioxide, the owner or operator of a smelter subject to Section 109 of this Part shall continue to calibrate, maintain and operate any ambient sulfur dioxide monitoring equipment owned by the smelter owner or operator and in operation on December 17, 1993.  Such monitors shall be operated and maintained as prescribed at 40 CFR Parts 53 and 58.  The location of ambient sulfur dioxide monitors and length of time such monitors remain at a location shall be determined by the Department.  [11-30-95]

 117. DATA SUBMISSION:  The data accumulated from the programs detailed in Sections 115 and 116 of this Part shall be submitted to the Department for its review.  The reports should confirm whether or not the emission limitations contained in Section 109 of this Part are adequate to maintain state and federal ambient air quality standards.  The Department, upon reasonable notice
and at reasonable times, shall have access to all raw and verified data for verification purposes and shall be permitted access to the monitors, and shall have the opportunity to perform quality assurance audits.  [11-30-95]