An official website of the United States government.

This is not the current EPA website. To navigate to the current EPA website, please go to www.epa.gov. This website is historical material reflecting the EPA website as it existed on January 19, 2021. This website is no longer updated and links to external websites and some internal pages may not work. More information »

Surface Coating of Metal Coil: National Emission Standards for Hazardous Air Pollutants (NESHAP)

On this page:

Rule Summary

This action promulgates national emission standards for hazardous air pollutants (NESHAP) for new and existing sources that coat metal coil. The final rule implements section 112(d) of the Clean Air Act (CAA) and will require all new and existing metal coil coating operations that are major sources to meet HAP emission standards reflecting the application of the maximum achievable control technology (MACT).

The EPA has identified metal coil surface coating as a major source of hazardous air pollutant (HAP) emissions such as glycol ethers, xylenes (isomers and mixtures), toluene, and isophorone. For existing sources in the metal coil coating industry, the nationwide baseline HAP emissions are estimated to be 2,258 Mg/yr (2,484 tpy). We estimate that implementation of the final rule will reduce emissions from these sources by 1,198 Mg/yr (1,318 tpy), or approximately 53 percent. Since the emission limits for new and existing sources are the same, emission reductions for new sources are expected to be similar to the 53 percent emission reduction estimated for existing sources. Emissions of the HAP methyl ethyl ketone (MEK) are included in the emissions inventory and emission reduction estimates for this source category. MEK has been delisted since promulgation of the final rule.

Rule History

2/25/2020 - Final Risk and Technology Review

06/04/2019 - Proposed Risk and Technology Review

03/17/2003 – Final Rule; Technical Correction

06/10/2002 – Final Rule

07/18/2000 – Proposed Rule

Additional Resources

Fact Sheet:  Final Risk and Technology Review Surface Coating of Metal Cans and Surface Coating of Metal Coil

Fact Sheet:  Proposed Risk and Technology Review Surface Coating of Metal Cans and Surface Coating of Metal Coil

Presentation on Residual Risk and Technology Review of Surface Coating NESHAP for the National Coil Coating Association Annual Meeting, held April 30, 2018(14 pp, 89 K, 4-30-2018)

Fact Sheet: Final Rule to Reduce Toxic Air Pollutant Emissions from Metal Coil Surface Coating Facilities

National Emission Standards For Hazardous Air Pollutants (NESHAP) Metal Coil Surface Coating Background Information For Promulgated Standards

The following links exit the site Exit

NOTE:  Most links on this page are pointers to other hosts and locations in the Internet. This information is provided as a service; however the U.S. Environmental Protection Agency does not endorse, approve or otherwise support these sites.

Steel Deck Institute. The Steel Deck Institute was formed to uniformity to design, manufacture, quality control and construction practices applicable to cold-formed steel decking. The SDI website is intended to keep designers and constructors up to date on deck design and construction and to provide information about the SDI and the member companies.

Aluminum Association. The Aluminum Association, Inc. is the trade association for producers of primary aluminum, recyclers and semi-fabricated aluminum products, as well as suppliers to the industry. Based in Washington, D.C., with offices in Detroit, Michigan, the Association provides leadership to the industry through its programs and services which aim to enhance aluminum's position in a world of proliferating materials, increase its use as the "material of choice," remove impediments to its fullest use, and assist in achieving the industry's environmental, societal, and economic objectives. Member companies operate about 200 plants in the U.S and many conduct business worldwide.

Related Rules

Control Techniques Guidelines for Miscellaneous Metal and Plastic Parts Coatings

Control Of Volatile Organic Emissions From Existing Stationary Sources: Surface Coating Of Miscellaneous Metal Parts and Products

Control of Volatile Organic Emissions from Existing Stationary Sources: Surface Coating for Insulation of Magnet Wire

Surface Coating of Metal Cans: National Emission Standards for Hazardous Air Pollutants (NESHAP)

Beverage Can Surface Coating Industry: New Source Performance Standards (NSPS)

Metal Coil Surface Coating: New Source Performance Standards (NSPS)

Miscellaneous Metal Parts and Products Surface Coating Operations: National Emission Standards for Hazardous Air Pollutants (NESHAP)

Compliance

Compliance Timeline for Compliance Timeline for Surface Coating of Metal Coil NESHAP

Applicability Determination Index (ADI).  The ADI is maintained by EPA's Office of Enforcement and Compliance Assurance (OECA) and provides a data base of memoranda dealing with applicability issues.  The database is searchable by Subpart.